Explanation of how the delay circuit works.

Om Blake Bartosh has shared with us the explanation as to how the delay circuit works as you may be eager to try it out on your Bitx. The Audio Mute circuit operates in the following way. The 555 timer is connected to the PTT switch and generates a 100 msec pulse when PTT is engaged and another 100 msec pulse when PTT is released. The 555 timer is configured as a debounce circuit, so contact bounce of the PTT switch does not initiate any new pulses. The output of the 555 timer and the PTT switch signal are combined in logic to form two signals, a mute command and a transmit command. The mute command turns on Q16 of the Exciter board which shorts the audio signal to ground, and no sound is heard from the speaker. The mute command occurs immediately upon engaging PTT, but the transmit command is delayed by 100 msec. This delay ensures audio transients due to switching from receive to transmit mode do not cause a "pop" in the speaker, but is not so long as to be noticeable to the operator. The transmit command energizes the relay coil of K2 of the PA board via a 2N3904 transistor and the rig switches to transmit mode. Upon releasing PTT the transmit command is immediately turned off, K2's relay coil is de-energized and the rig reverts to receive mode. 100 msec later the mute command is turned off and the speaker is activated again. The Audio Mute circuit is powered by 12V+, and a voltage regulator reduces the 12V+ voltage to +5VDC required by the 555 timer and the 74LS00 quad NAND gate IC.

Bitx3B VFO

The Bitx3B has a Varactor tuned VFO using MV209 and the stability is controlled with the Ik3OIL FLL Freq counter which has an inbuilt software to correct the drift in the VFO.

Building a stable vfo is an art and if not built correctly it would not perform optimum.

Picture and Video  below outlines some important factors that could enhance the performance.

BITX 3 B VFO SECTION

Outlined below are some points that need to be performed on the VFO section of Bitx3b for a drift free VFO

1.  VFO Capacitors to be NPO or Polystyrene

2. L5 VFO coil to be wounded tightly, placed flat on board and   applied  with thin layer of glue, quick fix is preferred as it has a thin layer, not very much to be applied, just enough to cover it.

3.MV209 And BB204  legs to be trimmed so that they may be just about near the board and soldered. A thin coating of quick fix could be applied on their sides, this way it becomes a sealed unit and gets protection from any air currents to extremely temperature.

4.It is better to use X position with 0.1uf  preferred Silver Mica /NPO or Polystyrene capacitor.  If you place a jumper across X then you may experience some drift, with 0.1uf in place the drift is manageable with the FLL counter attached.

5.  For FLL Freq counter Input and Contol it is recommended to use Rg174u coax

 6. Adjustment of Trimmer on control side of FLL is very important. The trimmer on extreme end of board is the trimmer that connects to the FLL control unit. Remember to fully mesh the trimmer or the vfo may drift.

The vfo was tested using the above recommendations and the test results:  2 Hours VFO On with max drift of 25Herts 

                   

Audio Mute Circuit For Bitx

Bitx had a problem of  noise being generated on pressing the PTT button. The usual way of muting the PIN 3 of LM386 did work  to solve the problem much, although to some extend, while working with Bitx3b i had discussion regarding this problem with Om Blake Bartosh from USA who was also building the Bitx Version3b  and who has also put in a great effort in bringing out the new Bitx3b construction manual.

The idea was to make a project to mute the audio of LM386 completely.
Presented below is a schematic of the audio mute circuit designed and tested by OM Blake Bartosh.

I myself build it and its working perfectly with my bitx3b. This circuit can be used for any tcvr.
The complete assembled kit will be available very soon.


                                           SCHEMATIC OF BITX AUDIO MUTE CIRCUIT                          

                                           VIDEO OF BITX AUDIO MUTE CIRCUIT                          

 

New Ham Radio TCVR Minima

Om Farhan from India has come up with another Ham Radio project. The new project is named Minima, which means a project with minimum components.

Minima is a complete ssb/cw tcvr with Arduino in it and an Si570.

Farhan's home page on minima is found here  http://www.phonestack.com/farhan/minima.html

 To carry on with our services we have decided to help amateurs buy our various products based on  Minima.

We are starting by selling the PCB developed by our forum member as very low cost, as to promote the building of Minima. Very soon we will provide a complete kit with case for Minima .

Please look out the availability  of the PCB set for Minima, which will be available very soon on our new blog meant for Minima.  http://cqminima.blogspot.com


We have also set up a new blog for  bitx version 3 B, which will be updated with all info on Bitx3B
http://bitxversion3b.blogspot.in/

Best of 73s

Sunil VU3SUA

Posted here are some pictures of my second built Bitx3B this one is with agc working. The earlier agc pcb had to be modified. The present agc/s.meter pcb mounts on the vu meter.

Bitx Ver 3 B RX demo

Some more new videos of Bitx Ver 3 B in receive mode.

Bitx Version 3 B Demo 3

Bitx Version 3 B Demo 2

Bitx Version 3 B SSB TCVR . Demo of RX

Here is a video i took last night for the Bitx Version 3 B in receive mode.

I have taken some more videos which i will post soon.

The receiver is quite sensitive and the VFO is quite stable.  Since it is a var actor VFO i am quite satisfied with its stability .  The maximum drift i observed in 12 to 15 hours not more then 50 to max 100 hertz in a period of 12  to 15 hours time.

More news of Bitx Version 3 coming soon.